EP brand replacement gearbox for woods rotary gearbox

EP model alternative gearbox for woods rotary gearbox

NEW 40 HP GEARBOX Smooth Input 1 3/eight twelve spline output Interchangable with market well-liked dimensions i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE A lot of More

(1) manufacturer new 45 horse electricity shearpin gearbox. This gearbox matches numerous different can make of 4′,5′ and some 6′ rotary cutters. I promote a lot of these packing containers each yr for several different purposes and have ALL Substitute Elements for this box, but with any luck , you will not have to fret about that.
Right here are the specs on the box:
*forty five horse power gearbox
*Regular 1-3/eight” easy input shaft(in which the pto shaft hooks on). The pto shaft is held on by a 1/two shearbolt.
*duration of the enter shaft out of the gearbox is three” long
*bolt hole sample for mounting is on the corners, four-three/4 centre of hole to centre of hole. It will take a five/8″ bolt.
*twelve splined output shaft(exactly where the blade carrier hooks up on the bottom)
*1-9/16 outside measurement over the output shaft splines- from the foundation of the output cap to the finish of the splines is two-3/4″ lengthy- general duration of the output shaft is 4-one/two” extended.
*requires a one” threaded castle nut and a carter important on the bottom of the output shaft to safe blade pan(NUT is provided – – BLADE PAN IS NOT!!)
*general peak of the box from the top of the mower deck to the prime of the box is 9-one/2″
This is a pretty heavy merchandise (47 lbs.) so freight is not cheap, but we do not make anything at all off of freight, what ever ups costs us we charge you.
forty HP
one:1:47 Ratio
one-3/eight” Smooth Input Shaft with Shear Pin Gap
one-one/2″ 12-Spline Ouput Shaft
Bolt Pattern: six-1/2″ (four) 5/8″ Holes, five” Heart Gap Necessary for Shaft Assembly
The Enter and Output Shafts Are not able to be Bought Serparately.
They are Offered as a kit.
The kit consists of the subsequent elements: enter shaft, enter equipment, output shaft, output gear.
The Shaft Kit Cannot Be Divided.

EP model alternative gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Information
Is your mower leaking, creaking or in any other case executing improperly? You’ve arrive to the appropriate spot.

Study underneath for the most common issues with rotary cutter gearboxes and their answers (from fast and filthy, to expert).

Leaking Base Seal:
If you’ve wrapped some baling or fencing wire close to your output shaft and blown the seal, the skilled point to do is to exchange the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing homes can get you up a generic double-lip seal that will get you back up-and-running. If not, give us a call and we can help you type out what you need to have.
A dental choose is the easiest way to remove the outdated seal just before pressing in the new one.
If you might be lucky sufficient to have a sluggish-leak, the quick and filthy method is to run automotive-variety grease in the gearbox until the new seal arrives in. Be positive to check out and include grease a lot more regularly than you would with oil, as this is NOT a specialist repair.

Broken Output Shaft:
Uh oh. You strike some thing that did not go. The good information is that the output shaft on most gearboxes is reasonably simple to exchange. The undesirable news is… it’s not often an isolated failure.
The first point to do is to get apart your gearbox and assess the complete extent of the damage. If it is really just the output shaft, you should be in a position to adjust it out, no issue. The output shafts start off at about $70 and go up in price relying on the dimension of the gearbox.
Even so, in most instances, the bearings ($20/ea), seals ($10/ea) and gear-set ($70) will also typically just take a beating. If you’re unlucky, the output cap ($80) will also undergo some hurt.
In this circumstance, it is generally less expensive to replace the gearbox. Compare the value of elements to the expense of an entire, new, warrantied gearbox. Sometimes, even professionals have to know when to call it a day.

I Want to Adjust my Enter Shaft:
If you are tired of altering shear pins or hunting again and seeing that your mower hasn’t been cutting, you may possibly want to set up a slip-clutch pto shaft (Of course, we market individuals too).
This normally demands installing a 540-type, 6-spline input shaft ($85) on your mower’s gearbox.
Lucky for you, we did a publish-up on our site. It is referred to as “How to adjust the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem type-of related over-the-telephone. The best thing to do is to disassemble your gearbox and just take a appear at the gears and bearings. The problem will typically current by itself in the way of damaged/lacking equipment teeth, toasted gears (like that photo on our residence webpage), or blown bearings.
If almost everything appears standard, attempt changing the gear-mesh. This is completed with the mylar “gaskets” that sit amongst the main gearbox circumstance and the input/output caps. Attempt including or getting rid of some of these spacers till your gears have roughly 1/8″-one/4″ of cost-free perform. Experts can purchase replacements ($1-two) in varying thicknesses, but we advocate the rapid and soiled technique of slicing your personal out of a sheet of mylar.
Do not overlook to re-seal the gearbox with RTV soon after you have discovered the correct mix. Even although they are called “gaskets”, they will not seal your gearbox on their own.

Interpump Gearbox For PTO Drive altered my life for the much better!


Recent Posts